3 Position Folding Legs and Lockable Leg Extensions Equipped with Nonslip Rubberized Foot Pads
Center Height Adjustable from 8.1″-11.9″
Low Profile Offset Picatinny Mount with Knurled Thumb Nut and Reinforced Steel Cross Bolt
Tunable Tension Adjustment Applies the Desired Amount of Tension to the Bipod’s 360° Panning & 15° Left, Right, Forward, and Rearward Tilt
Readjustable Tension Adjustment Lever is User Serviceable and Optimizes the Applied Tension with the Lever’s Throw Distance and Positioning
Durable Aircraft Aluminum Construction Finished in a Matte Black Anodization
US PAT. D758521, US PAT. D758522
Fine-tune Adjustment
Tension Adjustment Throw Lever is User Friendly and Serviceable being re-adjustable over time.
While holding the lever in place, use a T15 Torx wrench to remove the screw and lever cap.
Pull the lever out and rotate the exposed hex nut clockwise to increase and counterclockwise to decrease the amount of tension applied by the lever.Reinstall lever to test lever tension. We recommend adjusting until max tension is achieved when the lever points straight down.
With max tension achieved, reinstall the lever with it pointing straight down.Using the T15 Torx wrench, reinstall the lever cap and screw. Recommended torque value is 15in-lbs.
Versatile Panning & Tilting
Smooth 360° planning with additional 15° forward, rearward, left, and right tilt.
0°, 45°, and 90° Foldable Positions with Posi-lock
Tension Adjustment Throw Lever is User Friendly and Serviceable being re-adjustable over time.
Press down and hold the Posi-lock release.
Turn the bipod leg to the desired position, releasing the Posi-lock once done to lock the bipod leg into place.
To position the legs to face rearward and away from the muzzle rotate the base along its panning axis 180 degrees.
Lockable and Adjustable Center Height
Tension Adjustment Throw Lever is User Friendly and Serviceable being re-adjustable over time.
Make sure the Locking Thumb Wheel is fully released by turning it counter-clockwise.
Extend the bipod leg by pulling it out of the leg housing. Set it at any of the pre-cut extension notches. Tighten the Locking Thumb Wheel by turning it clockwise to lock the leg.
To retract the bipod leg, loosen the Locking Thumb Wheel first. Press down the Leg Retraction Clamp before you push the extended leg upward into the housing.
ACCESSORIES INCLUDED
Swivel Stud Adaptor
User Manual
Lisainfo
Tootjakood:
TL-BP03-B
Küpsiste nõusoleku haldamine
Parima kogemuse pakkumiseks kasutame seadmeteabe salvestamiseks ja/või sellele juurdepääsemiseks selliseid tehnoloogiaid nagu küpsised. Nende tehnoloogiatega nõustumine võimaldab meil töödelda selliseid andmeid nagu sirvimiskäitumine või unikaalsed ID-d sellel saidil. Nõusoleku mittenõustumine või tagasivõtmine võib teatud funktsioone ja funktsioone kahjustada.
Functional
Always active
The technical storage or access is strictly necessary for the legitimate purpose of enabling the use of a specific service explicitly requested by the subscriber or user, or for the sole purpose of carrying out the transmission of a communication over an electronic communications network.
Preferences
The technical storage or access is necessary for the legitimate purpose of storing preferences that are not requested by the subscriber or user.
Statistics
The technical storage or access that is used exclusively for statistical purposes.The technical storage or access that is used exclusively for anonymous statistical purposes. Without a subpoena, voluntary compliance on the part of your Internet Service Provider, or additional records from a third party, information stored or retrieved for this purpose alone cannot usually be used to identify you.
Marketing
The technical storage or access is required to create user profiles to send advertising, or to track the user on a website or across several websites for similar marketing purposes.
Tasu kolme võrdse maksena 3 x 55.04 €
